Peugeot 406

since 1996 release

Repair and operation of the car


Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. Suspension bracket and steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward hug bearings
   11.4. The lobby is resistant
   11.5. Repair of a forward rack
   11.6. Lower lever of a forward suspension bracket
   11.7. Lower spherical hinge of a forward suspension bracket
   11.8. Stabilizer of cross stability of a forward suspension bracket
   11.9. Coulisse of the stabilizer of cross stability of a forward suspension bracket
   11:10. Lower frame of a forward suspension bracket
   11:11. Nave of a back wheel
   11:12. Replacement of bearings of a back nave
   11:13. Shock-absorber of a back suspension bracket
   11:14. Cylindrical spring of a back suspension bracket
   11:15. Pin of a nave of a back suspension bracket
   11:16. Lower lever of a back suspension bracket
   11:17. Top lever of a back suspension bracket
   11:18. The directing lever of a back suspension bracket
   11:19. Draft of a back suspension bracket
   11:20. Stabilizer of cross stability of a back suspension bracket
   11:21. Coulisse of the stabilizer of cross stability of a back suspension bracket
   11:22. Steering wheel
   11:23. Steering column
   11:24. Intermediate shaft of a steering column
   11:25. Ignition lock
   11:26. Steering mechanism
   11:27. Replacement of protective covers of the steering mechanism
   11:28. Removal of air from system of steering with the amplifier
   11:29. Pump of the amplifier of steering
   11:30. Spherical hinge of steering draft
   11:31. Steering draft
   11:32. Angles of installation of wheels
+ 12. Body
+ 13. Electric equipment
+ 14. Main malfunctions


7f75ccd3



11.4. The lobby is resistant

Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and record on supports. Remove the corresponding forward wheel.
2. Disconnect electric wires and hoses from a rack.
3. Unscrew bolts of fastening and exempt an installation suspension bracket from a rotary fist.
4. Unscrew a nut of fastening of the lower spherical hinge and take the spherical hinge from the lower lever.
5. Unscrew a nut of fastening of the coulisse of the stabilizer of cross resistance to a rack and separate the coulisse from a rack.
6. Unscrew a nut of a tightening bolt of a rotary fist.
7. Take tightening a bolt of fastening are resistant to a rotary fist. For prevention of lowering of a rotary fist with a nave at removal of a rack tie a wire the lower lever or a nave to the lower frame.
8. Take a rack from a rotary fist. If the rack sits densely in a rotary fist, using the big screw-driver, unclench a clip of a rotary fist.
9. In a motor compartment remove a protective plastic cap from the top part of a forward rack.
10. Unscrew 3 bolts of the top fastening of a forward rack.
11. Take a rack from under a wheel arch. Temporarily arrange the lower spherical hinge of a rotary fist in the lower lever.

Installation

PERFORMANCE ORDER
1. Establish a forward rack into place so that the adjusting pin of a plate of the top fastening correctly settled down in the corresponding opening. Combine the lower end of a rack with a rotary fist. At the same time it is necessary to combine a crack in a clip of a rotary fist with a ledge on the end of a rack.
2. Screw the top bolts of fastening of a rack and tighten them the required moment.
3. Make sure that the lower part of a rack is precisely combined with a rotary fist. Insert tightening a bolt from the back party of the car and fix it by a new nut.
4. Screw the lower spherical hinge of a rotary fist on the lower lever.
5. Connect the coulisse of the stabilizer of cross stability to a rack.
6. Fix electric wires and hoses on a rack arm.
7. Establish a wheel and lower the car.

On the homepage