Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
- 10. Brake system
   10.1. Technical data
   10.2. Pumping of the hydraulic brake system
   10.3. Brake pipelines and hoses
   10.4. Replacement of front brake shoes
   10.5. Replacement of back brake shoes
   10.6. Replacement of back brake shoes on drum brakes
   10.7. Forward brake disk
   10.8. Back brake disk
   10.9. Back brake drum
   10:10. Support of a forward brake
   10:11. Support of a back wheel
   10:12. Back brake cylinder
   10:13. Main brake cylinder
   10:14. Brake pedal
   10:15. Vacuum amplifier of brakes
   10:16. Unilateral valve of the vacuum amplifier of brakes
   10:17. Adjustment of the emergency brake
   10:18. Lever of the emergency brake
   10:19. Cable of the emergency brake
   10:20. Brake shoes of the emergency brake (model with disk brakes)
   10:21. The valve of adjustment of pressure in the brake system
   10:22. Stoplight switch
   10:23. Anti-blocking system of brakes (ABS)
   10:24. The vacuum pump (cars with the diesel engine)
   10:25. Check of the vacuum pump on cars with diesel engines
+ 11. Suspension bracket and steering
+ 12. Body
+ 13. Electric equipment
+ 14. Main malfunctions


7f75ccd3



10.6. Replacement of back brake shoes on drum brakes

GENERAL INFORMATION

Arrangement of elements of adjustment of brake shoes

1. The fixing regulator bolt spring

2. Regulator level spring

3. Top returnable spring

4. Adjusting element

Prevention

Surely you make replacement of all blocks on one axis of the car even if the limit of wear was reached by one block. If blocks are repeatedly established, before removal mark them.


PERFORMANCE ORDER
1. Remove the brake drum.
2. Observing care and security measures, clear all traces of brake dust from the brake drum, a brake board and blocks.
3. Measure thickness of overlays of brake shoes in several points. If at least one block is worn-out in any place to the minimum thickness, replace all 4 brake shoes.
4. Note the adjusting provision of all elements of a back brake. Using flat-nose pliers, remove a plate of a spring of fixing of a block, pressing a plate and turning it on 90 °. Remove springs and take clamp pins.
5. Remove one brake shoe from the lower support of blocks and disconnect the lower returnable spring.
6. Wring out both blocks from the wheel brake cylinder and remove them. At the same time do not damage boots. Disconnect a cable of the drive of the emergency brake from a brake shoe. For prevention of drop-out of pistons of the working brake cylinder fix pistons by the corresponding elastic band or a wire.
7. Note an arrangement of details of the regulator of brake shoes, remove the lever of the drive of the emergency brake and disconnect the fixing regulator bolt spring from a lobby (on an arrangement) a brake shoe. Disconnect the top returnable spring, separate a front brake shoe and a returnable spring from a back brake shoe. Disconnect the spring fixing the regulator to a back brake shoe (see rice. Arrangement of elements of adjustment of brake shoes).
8. Replace all returnable springs irrespective of their state.
9. Unscrew a bolt of fastening of the regulator to an adjusting level and check their state. Pay special attention to a carving of a bolt of the regulator and a side of an adjusting wheel. Pay attention that the left and right adjusting levels are not interchanged. Bolts of the regulator of the right and left wheel are also not interchanged. The bolt of the regulator of the left wheel has the left carving, and the bolt of the regulator of the right wheel has the right carving.
10. Check that all details on the end of an adjusting level are correctly placed, then apply a small amount of lubricant with high temperature of melting on a regulator bolt carving. Screw an adjusting wheel on a regulator bolt so that between a wheel and a head of a bolt there was a small gap. Insert a regulator bolt into an adjusting level.
11. Establish a returnable spring on back (on an arrangement) a brake shoe so that shorter hook of a spring connected to a block. Establish an adjusting level by the end of a spring. Insert an adjusting level into a groove in a back brake shoe.
12. Establish the top returnable spring on a back brake shoe. Establish the second end of a spring on a front brake shoe and, moving, arrange a forward block so that the head of an adjusting bolt settled down in a flute. After that insert a hook of the fixing spring into a groove on a front brake shoe.
13. Raise rubber protective covers of the brake cylinder and check the working brake cylinder for leak of brake fluid.
14. Clear details of a back brake. Apply lubricant with high temperature of melting on places of contact of blocks with a brake board.
15. Check that the lever of the emergency brake is located opposite to an edge of a back brake shoe, and remove the elastic band fixing pistons in the brake cylinder.
16. Stretch brake shoes and establish their top ends on the piston of the working brake cylinder. Connect a cable of the emergency brake to the lever of the emergency brake located on a back brake shoe. Establish the lower returnable spring on both brake shoes, establish the lower part of brake shoes on a support of blocks.
17. Moving brake shoes, center them in relation to a brake board. Establish pins of a clamp of a block, a spring and a plate of fastening of a spring.
18. Using the screw-driver, turn a wheel of an adjusting level so that to unclench brake shoes to a contact of the brake drum.
19. Install the brake drum.
20. Make replacement of brake shoes on the second back wheel.
21. After replacement of brake shoes adjust a gap between them and the brake drum for what several times press a brake pedal. When pressing a pedal during the normal work of an adjusting level the clicks published by an adjusting level have to be heard.
22. Check and if it is necessary, adjust the emergency brake.
23. Check the level of brake fluid in system.

On the homepage