Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. Suspension bracket and steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward hug bearings
   11.4. The lobby is resistant
   11.5. Repair of a forward rack
   11.6. Lower lever of a forward suspension bracket
   11.7. Lower spherical hinge of a forward suspension bracket
   11.8. Stabilizer of cross stability of a forward suspension bracket
   11.9. Coulisse of the stabilizer of cross stability of a forward suspension bracket
   11:10. Lower frame of a forward suspension bracket
   11:11. Nave of a back wheel
   11:12. Replacement of bearings of a back nave
   11:13. Shock-absorber of a back suspension bracket
   11:14. Cylindrical spring of a back suspension bracket
   11:15. Pin of a nave of a back suspension bracket
   11:16. Lower lever of a back suspension bracket
   11:17. Top lever of a back suspension bracket
   11:18. The directing lever of a back suspension bracket
   11:19. Draft of a back suspension bracket
   11:20. Stabilizer of cross stability of a back suspension bracket
   11:21. Coulisse of the stabilizer of cross stability of a back suspension bracket
   11:22. Steering wheel
   11:23. Steering column
   11:24. Intermediate shaft of a steering column
   11:25. Ignition lock
   11:26. Steering mechanism
   11:27. Replacement of protective covers of the steering mechanism
   11:28. Removal of air from system of steering with the amplifier
   11:29. Pump of the amplifier of steering
   11:30. Spherical hinge of steering draft
   11:31. Steering draft
   11:32. Angles of installation of wheels
+ 12. Body
+ 13. Electric equipment
+ 14. Main malfunctions


7f75ccd3



11.2. Rotary fists

GENERAL INFORMATION

Prevention

At installation it is necessary to use new nuts of the spherical hinge of steering draft, the lower spherical hinge and tightening a bolt and a nut of a rotary fist.


Removal

PERFORMANCE ORDER
1. Take off a wheel nave cap, take a R-shaped bracket.
2. Remove a blocking head from a lock nut of a power shaft. Weaken a nut of a power shaft on the car standing on wheels. Also weaken bolts of fastening of a wheel.
3. Lift a forward part of the car and record on supports. Remove the corresponding forward wheel.
4. On the cars equipped with ABS unscrew a bolt of fastening of the sensor installed on a wheel of the car and take the sensor from a rotary fist.
5. Unscrew a nut of fastening of a power shaft.
6. Unscrew a nut, the fixing steering thirst for a rotary fist and take the spherical hinge of steering draft from a rotary fist. For extraction of the spherical hinge of steering draft from a rotary fist it is necessary to use a universal stripper of spherical hinges.
7. Remove a brake disk.
8. If it is necessary, unscrew bolts of fastening of a suspension bracket (are specified by shooters) to the top part of a rotary fist.
9. Unscrew a nut of fastening of the lower spherical hinge and take a pin of the spherical hinge from the lower lever.
10. Unscrew a nut and take tightening a bolt of a rack of a rotary fist, noting that the bolt is established from the back party of the car. At installation it is necessary to use new tightening a bolt and a nut.
11. Remove a rotary fist from the end of a rack and from shlits of a power shaft. Remove it from the car. If the rotary fist densely sits on the lower part of a rack, use the big screw-driver for a release of a clip of a rotary fist.

Installation

PERFORMANCE ORDER
1. Make sure that vents on the external end of a power shaft and grooves in a nave pure. Pull a nave over grooves of a power shaft.
2. Pull a rotary fist over the lower part of a rack of a suspension bracket, leveling a crack in a rotary fist with a ledge on the end of a rack. Insert new tightening a bolt from the back party of the car, screw a nut on a bolt and tighten the required moment.
3. Combine the lower spherical hinge with the lower lever and fix it with use of a new nut.
4. Connect the spherical hinge of steering draft to a rotary fist and fix by a new nut.
5. Establish a brake disk.
6. On the models equipped with ABS install the sensor of rotation of a wheel.
7. Grease an internal part and a carving of a nut of fastening of a power shaft with pure engine oil and screw a nut on a power shaft. Fix a nut of fastening of a power shaft by the required moment. Check that the nave rotates freely, establish a head of blocking of a nut of a power shaft so that one of safety locks was combined with an opening of a power shaft and record it a R-shaped bracket.
8. Establish a wheel and lower the car.
On the homepage