Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
- 13. Electric equipment
   13.1. Technical data
   13.2. Detection of not closed chain
   13.3. Safety locks and relay
   13.4. Switches
   13.5. Bulbs of external lighting
   13.6. Lighting lamps of salon
   13.7. Devices of external lighting
   13.8. Adjustment of light of headlights
   13.9. Combination of devices
   13:10. Multipurpose display
   13:11. Lighter
   13:12. Hours
   13:13. Sound signal
   13:14. Screen wiper lever
   13:15. Engine of a screen wiper and draft
   13:16. Back screen wiper
   13:17. Windscreen washer
   13:18. Automobile radio tape recorder
   13:19. Column (dynamics)
   13:20. Antenna
   13:21. Control system cruise control
   13:22. Anticreeping system and immobilizer of the engine
   13:23. Electric units of forward sitting
   13:24. Safety cushion
   13:25. Safety cushion elements
   + 13:26. Electric circuits
+ 14. Main malfunctions


7f75ccd3



13.4. Switches

GENERAL INFORMATION

Prevention

Before removal of any switch remove the negative plug from the accumulator.


Removal and installation

SWITCH OF THE STEERING COLUMN


PERFORMANCE ORDER
1. Unscrew screws of fastening of the lower casing of a steering column and remove the top and lower casings from a steering column. Disconnect the electric socket from a cruise control.
2. Disconnect the electric socket from the switch, unscrew fastening screws (are specified by shooters a photo at the left) and take the switch from a steering column (a photo on the right).
3. Installation is made in the sequence, the return to removal (screws of fastening are specified by shooters).

KRUIZ-KONTROLYA SWITCH

PERFORMANCE ORDER
1. Unscrew screws of fastening of the lower casing of a steering column, disconnect the electric socket and remove the lower casing.
2. Unscrew fastening screws (are specified by shooters) and remove the switch a cruise control from the lower casing of a steering column.
3. Installation is made in the sequence, the return to removal.

DASHBOARD SWITCHES

PERFORMANCE ORDER
1. Open an immobilizer cover, turn a clip on 90 ° and uncover a box with fuses.
2. Unscrew screws (are specified by shooters) fastenings of the basis of group of switches.
3. Remove group of switches from the dashboard and disconnect the electric socket.
4. For removal of the separate switch from group of switches wring out brackets of blocking and remove the switch.
5. Installation is made in the sequence, the return to removal.

SWITCHES OF THE CENTRAL PART OF THE DASHBOARD


PERFORMANCE ORDER
1. Remove the multipurpose display. On cars without display separate the right side of the switch by means of the thin screw-driver from a ware box.
2. Remove a frame of switches.
3. Unscrew screws (are specified by shooters) fastenings and remove group of switches from the dashboard.
4. Disconnect electric sockets and remove each switch separately from others.
5. Installation is made in the sequence, the return to removal.

SWITCHES OF THE CENTRAL CONSOLE


PERFORMANCE ORDER
The switch of the central console can be taken from a nest after the central console is unscrewed from a car floor.

GROUP OF SWITCHES ON THE DOOR

PERFORMANCE ORDER
1. By means of the thin screw-driver remove a decorative overlay of switches on a car door.
2. By means of the lever take the switch from a nest on a door (a photo at the left) and disconnect from it the electric socket (a photo on the right).
3. Installation is made in the sequence, the return to removal.

SWITCHES OF THE TOP CONSOLE

PERFORMANCE ORDER
1. Uncover a back part of the top console.
2. Unscrew 2 screws (are specified by shooters) fastenings and lower the top console down.
3. Disconnect electric sockets and take the top console from the car.
4. For removal of the switch of the hatch unscrew screws (are specified by shooters a photo at the left) fastenings of the printed circuit board and take the switch from top (a photo on the right). Other switches are a component of the top console and cannot separately be replaced.
5. Installation is made in the sequence, the return to removal.

SWITCHES OF SEATS

PERFORMANCE ORDER
1. Being careful, by means of the lever take the switch from the side lower part of a seat and disconnect from it the electric socket.
2. Connect the electric socket to the switch and establish it into place.

SWITCH OF THE CONTROL LAMP OF TURNING ON OF THE EMERGENCY BRAKE

PERFORMANCE ORDER
1. Remove the central console.
2. Disconnect the electric socket from the switch of a control lamp of turning on of the emergency brake, disconnect the switch and remove from the lever of the emergency brake.
3. Installation is made in the sequence, the return to removal.

SWITCH OF ILLUMINATION OF SALON

PERFORMANCE ORDER
1. Open a door and remove a rubber cover from the switch located on a door rack.
2. Release clamps and being careful take the switch from a rack.
3. Disconnect from it the electric socket, tie to the wires going to the switch, a thin cord.
4. Installation is made in the sequence, the return to removal.

LUGGAGE CARRIER ILLUMINATION SWITCH

PERFORMANCE ORDER
1. On cars the sedan (Saloon) open a trunk lid, take percussion caps and remove finishing of a luggage carrier.
2. On models of a komba (Estate) open a back door, unscrew screws and remove the internal handle of a back door. Using the thin screw-driver, remove decorative finishing of the internal button of the lock.
3. Unscrew bolts, remove the switch and disconnect from it the electric socket.
4. Installation is made in the sequence, the return to removal.

SCREEN WIPER RAIN SENSOR

PERFORMANCE ORDER
1. Remove the case of an internal rear-view mirror from the inside of a windshield, having pulled it down.
2. Disconnect the electric socket, disconnect brackets of fastening and remove the rain sensor from a windshield.

Prevention

Do not touch by hands of a lens of the sensor of a rain or a windshield in the field of installation of the sensor since for normal operation of the sensor its lens and a windshield have to be absolutely pure.


3. Installation is made in the sequence, the return to removal.

On the homepage