Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
- 13. Electric equipment
   13.1. Technical data
   13.2. Detection of not closed chain
   13.3. Safety locks and relay
   13.4. Switches
   13.5. Bulbs of external lighting
   13.6. Lighting lamps of salon
   13.7. Devices of external lighting
   13.8. Adjustment of light of headlights
   13.9. Combination of devices
   13:10. Multipurpose display
   13:11. Lighter
   13:12. Hours
   13:13. Sound signal
   13:14. Screen wiper lever
   13:15. Engine of a screen wiper and draft
   13:16. Back screen wiper
   13:17. Windscreen washer
   13:18. Automobile radio tape recorder
   13:19. Column (dynamics)
   13:20. Antenna
   13:21. Control system cruise control
   13:22. Anticreeping system and immobilizer of the engine
   13:23. Electric units of forward sitting
   13:24. Safety cushion
   13:25. Safety cushion elements
   + 13:26. Electric circuits
+ 14. Main malfunctions


7f75ccd3



13.7. Devices of external lighting

GENERAL INFORMATION

Prevention

Before removal of devices of lighting remove the negative plug from the accumulator.


Removal and installation

HEADLIGHTS

PERFORMANCE ORDER
1. Open a cowl and remove connectors of fastening of a front grille.
2. By means of the screw-driver disconnect brackets of fastening and remove a lattice.
3. Unscrew nuts of fastening of a casing of the fan to the cowl lock. Unscrew bolts (are specified by shooters) fastenings of the lock of a cowl and disconnect from it a cable.
4. Disconnect a cable from the lock of a cowl and remove the lock.
5. From under a wheel arch by means of the small screw-driver remove a cap for access to a spring of fixing of a headlight.
6. By means of flat-nose pliers or a special core disconnect a spring of fixing of a headlight to a car body.
7. Unscrew 3 bolts of fastening of a headlight.
8. Disconnect the electric socket (a photo at the left) and take a headlight (a photo on the right).
9. On the cars equipped with the proofreader of light of headlights remove the proofreader's engine from a back part of a headlight, turning it counterclockwise.
10. Being careful, disconnect the spherical hinge from a back part of a reflector of a headlight.
11. Installation is made in the sequence, the return to removal.

FOG LIGHT

PERFORMANCE ORDER
1. Lift a forward part of the car and record on supports. Unscrew screws and remove plastic protection from the lower part of a fog light.
2. Disconnect the electric socket and unscrew the lower screw of fastening of a headlight.
3. Disconnect the top fixing spring and take a headlight from the lower forward part of a bumper.
4. Installation is made in the sequence, the return to removal.
5. For adjustment of light of a fog light, using a special key, turn the regulator on a back part of a headlight. If the plastic sheeting of the lower part of a headlight is removed, the regulator of light of a headlight can be turned a hand.

BACK LAMP ON MODELS THE SEDAN (SALOON)

PERFORMANCE ORDER
1. Unscrew screws of fastening and remove back finishing of a luggage carrier. Take percussion caps and remove a back upholstery of a luggage carrier. On some models for access to the left back lamp unscrew a clip and remove office of storage.
2. Release brackets and disconnect the electric socket from a back lamp.
3. Unscrew nuts (a photo at the left) and remove a back lamp (a photo on the right).
4. Installation is made in the sequence, the return to removal.

BACK LAMP ON THE WING OF THE KOMBI (ESTATE) CAR

PERFORMANCE ORDER
1. Uncover office of storage in a luggage compartment.
2. Remove a fastening bracket, disconnect the electric socket, unscrew a nut (it is specified by an arrow) fastenings and remove a back lamp from a car wing.
3. Installation is made in the sequence, the return to removal.

THE BACK LAMP LOCATED ON THE BACK DOOR OF THE KOMBI (ESTATE) CARS

PERFORMANCE ORDER
1. Open a back door and remove from it an upholstery.
2. Release a bracket and disconnect the electric socket. Unscrew nuts (are specified by shooters a photo at the left) fastenings and remove a back lamp from a back door.
3. Installation is made in the sequence, the return to removal.

ADDITIONAL TOP STOPLIGHTS

PERFORMANCE ORDER
Models sedan (Saloon)
1. Using a curved core, insert it into lamp clamps, release brackets of fastening and pull a lamp down.
2. Shift a lamp back, release from guides, take from the car and disconnect the electric socket.
3. Installation is made in the sequence, the return to removal.
Models of a komba (Estate)
4. Open a back door and remove screws (are specified by shooters) fastenings of a spoiler from the top part of a door.
5. Remove a spoiler, disconnect the electric socket (1) and a hose (2) washers of back glass and take them from a back door (3 – screws of fastening additional a sling signal and a spoiler).
6. Installation is made in the sequence, the return to removal.

LAMP OF ILLUMINATION OF REGISTRATION PLATE


PERFORMANCE ORDER
Models sedan (Saloon)
1. Take a lamp of illumination of registration plate from a rear bumper (a photo at the left) and disconnect the electric socket (a photo on the right).
2. Installation is made in the sequence, the return to removal.
Models of a komba (Estate)
3. Open a back door, unscrew screws and remove the internal handle. Remove a decorative overlay of the internal button of the lock. Remove finishing of a back door.
4. Disconnect the electric socket from a back part of a lamp (a photo at the left) and take a lamp from a back door (a photo on the right).
5. Installation is made in the sequence, the return to removal.

On the homepage